Torque Specifications for Rear U Bolts on F53 Chassis Motorhome
Question:
What would you say the torque specs would be on those huge u bolt that hold the rear springs ? Not sure i have the right torque wrench?? Thanks
asked by: Mario
Helpful Expert Reply:
The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1 5/16" or 33mm socket to remove the nuts) they torque to 400 lb-ft.
Typically most 1/2 drive torque wrenches only go up to 250 lb-ft, so a 3/4" drive torque wrench or bigger is recommended, the additional length will also provide the leverage you'll need to reach the torque value. It is recommended that you recheck the torque after driving for a while because the suspension can settle and the bolts may not be tight enough.
One piece of advice I can give you is to have an extra set of hands help. You can turn the torque wrench while your helper holds the socket on the nut so it doesn't slip. It can be challenging to hold the socket on, and reach far out enough to turn the wrench.
Product Page this Question was Asked From
Roadmaster Rear Anti-Sway Bar - 1-5/8" Diameter
- Anti-Sway Bars
- Anti-Sway Bar
- Rear
- 1-5/8 Inch Diameter
- Steel w Polyurethane Bushing
- Roadmaster
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Vehicle Sway Bars
- Shop: Roadmaster Front Anti-Sway Bar - 1-3/4" Diameter
- Shop: Roadmaster Rear Anti-Sway Bar - 1-5/8" Diameter
- Shop: Suspension Enhancement
- Shop: Roadmaster Rear Anti-Sway Bar - 1-1/2" Diameter
- Shop: Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets for Class A Motorhomes
- Search Results: steering stabilizer
- Shop: Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes
- Shop: Roadmaster Front Anti-Sway Bar - 2-1/8" Diameter
- Shop: Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets for Class A Motorhomes
- Video: Roadmaster Rear Anti-Sway Bar Installation - 2016 Ford F-53 RM-1139-149
- Video: Roadmaster Rear Anti-Sway Bar Installation - 2009 Workhorse W-Series
- Video: Roadmaster Exact Center Steering Stabilizer Installation - 2021 Ford F-53
- Video: Roadmaster Rear Anti-Sway Bar Review 1139-144
- Video: Roadmaster Exact Center Steering Stabilizer Review RM63RR
- Q&A: What Torque Should Be Used For U-Bolt Nuts On Trailer Suspension
- Search Results: rm~1139~146
- Search Results: front swaybar
- Search Results: roadmaster rear sway bar
- Search Results: trac bar
- Video: Roadmaster Exact Center Steering Stabilizer Installation - 2004 Ford F-53
- Video: Roadmaster Rear Anti-Sway Bar Installation - 2018 Thor Windsport Motorhome
- Q&A: Installing Extended U-bolts for Roadmaster Rear Anti-Sway Bar 1139-143 on 2004 F-53 Chassis
- Article: Stability Control for Heavy Duty Vehicles
- Article: RV Sway Control, Stabilization, and Suspension Enhancement
- Shop: Trailer Hitch
- Search Results: ssf~173~40~2
- Shop: Base Plate for Tow Bar
- Shop: Trailer Wiring
- Q&A: Recommendation for Roadmaster Front and Rear Sway Bars for a 2005 Fleetwood Bounder 34F
Ron J.
7/18/2020
I have a 2020 Thor Hurricane 29M on a 2019 chassis. I am going to install a RM steering stabilizer. Are the torque specs the same for the front suspension and rear suspension?